• This forum is the machine-generated translation of www.cad3d.it/forum1 - the Italian design community. Several terms are not translated correctly.

ansys

  1. sliding protusion with "scale" and "winding" option

    Hello everyone and thank you for accepting me in the forum, I would like to ask you for help: I am trying to create a geometry for a rotating tool, type tip of a drill, in which basically I have a fixed-shaped cross section but that during the extrusion should scale and rotate, as in the...
  2. problems with data entry in ansys 2023

    Good morning, they're cristian, mechanical engineering student at the bari polytechnic. I'm finding problems in entering data through text document in ansys, since every time I try to insert it gives me as an error "error reading coordinates file" . the nodes I copied them from airfoil tools...
  3. compression test

    I would like to make a test with this kind of damage on ansys, could someone guide me on how to do it? first static or dynamic? grate
  4. how to insert a damage criterion on ansys

    Hi guys, I need to insert the damage criterion on ansys, in particular a "max plastic strain equivalent" beyond which the program no longer takes into consideration that requested part and therefore excludes it from the calculation. Could you guide me? Thank you.
  5. symmetry problems

    Good morning guys, I'm simulating a simple compression test on a test that has 2 symmetry levels. in practice to speed the calculations I reproduced only 1/4 of the geometry and assigned the symmetry. But as you see from deformation there is something wrong. Can you tell me where I'm wrong? as...
  6. reticular structure analysis in ansys

    Hello, everyone. I ask you for help because I have to make on ansys a model that simulates the results found in the laboratory on trials that have a " latex" structure. the material in question is a ti6al4v alloy. 3d was created with solidworks. inserting the various parameters derived from the...
  7. ansys fluent cilindro

    Hello everyone, my name is luca and I am a mechanical engineering student struggling with the three-year thesis. I chose to ask for it experimental to fluiddynamics and I was assigned the classic flow problem on a cylinder to analyze with software fluent students version, with mesh limited to...
  8. orthotropic materials modal analysis

    hi to everyone, I just joined this forum as I would like some suggestions for a teaser I have to perform. I am a mechanical engineering student and for an examination I was asked to look for relationships between properties (e, g, nu) that define an orthotropic material of a mechanical component...
  9. how to specify the position of the knots in a solid 3d part in ansys mechanical?

    Bye to all, I tried to insert knots in specific positions in the mesh of a solid body 3d in ansys mechanical, unfortunately without success. Does anyone know how I can do that? I discovered that you could create hardpoints before generating mesh to have nodes in the location of those...
  10. .dat file (ansys) - compatibility with nastran

    Hello, everyone, I need some tips... . I have no fe modeler, and I need to transfer inputs both fem and geometric that can be read by nastran (so basically .dat file and/or .bdf file). use ansys workbench 18.2. I managed to export the mesh to .bdf exporting the result file to .stl and...
  11. aggiungere un nuovo "static structure" al "project tree" in ansys wb mech

    Hello. I'm a domenic student in engineering. I have to use ansys (version 7.12) for a research job and with no few difficulties I try to learn the program. Today I have the problem of having to add a new "static structure" to the "project tree" in ansys wb mechanical. Any of you have any idea...
  12. ansys - contact for simulation seal

    Good evening to all boys, I wanted to ask you some advice to prepare a calculation: what is the most suitable contact in ansys to simulate the behaviour of two flanges connecting pressure tubes? that, in other words, guarantee a stagnation. thanks in advance
  13. test a compressione

    Good evening, everyone! ! I am a graduate of materials ing. for a small part of my doctoral thesis I would need to carry out a compression test of a square section audition on ansys to assess the distribution of tension. Unfortunately, not being very practical of ansys, I am having some...
  14. analisi modale in workbench ansys

    good day to all users of cad3d.it!:biggrin: I wanted to ask a question about modal analysis in workbench ansys. We start from the fact that I have an assembly of many components, then I thought of doing a modal analysis since I subsequently intend to go to charge it with forceful employees from...
  15. find id of the knots of a helmet

    Hello. I am a mechanical engineer, and I am involved in aerodynamic design of turmoil, and for this I am a little bit unloaded (a little...:biggrin:) in the use of software for mechanical analysis like ansys. In general, mechanical analyses take care of their colleagues in cold mechanics, but...
  16. different materials

    Hey, everybody. I have a problem with ansys apdl. I practically have the classic dog bone test only which is formed by several different materials (bimetallic joint). I designed the structure on apdl but do not know how to insert the different materials in the different parts. Can any of you...
  17. structural simulation disc brake

    Hello everyone! I should lead to a structural static the stresses of a brake disc during a braking (completed disk image). I know the pressure of the brake fluid inside the brake transient (which is constant) of the circuit and therefore I can know the normal forces at the surface exercised by...
  18. libreria ansys - data source - pa 66 + 30gf - metal replacement

    Bye to all, I wanted to know if there is someone who has ever worked with a polyamide 6,6 (nylon 66) reinforced with glass fiber and if you can direct me to the characterization of the material in ansys. I am looking on the internet if there are material libraries to load, unfortunately I am not...
  19. static + structural fluent + acp

    Hello everyone! I have to study the structure of a plane's tail plane. I can't import the fluent pressure field to the static structural if I put between the two the acp module pre... I attach the system scheme to ansys workbenchthe resulting error message is: an error logged while trying to...
  20. ansys mechanical-problem with friction in cyclic symmetry

    Hello everyone, my goal is to create a cyclic symmetry with connected parts between them by contact frictional.I then inserted a thin surface and l/I connected in such a way with my part. Then I applied the symmetry.The problem is that while being present both bodies repeated, the results in...

Forum statistics

Threads
44,997
Messages
339,767
Members
4
Latest member
ibt

Members online

No members online now.
Back
Top