quadro fx 1800

[Be_on_edge]

Hey, guys.

any of you use the video card on 32-bit xp?

I have a problem, and I wanted to see if it's my card to be defective or it's a solid edge problem.

Thank you.

 

[radio]

in the office we have a couple of ws with xp32 and picture 1800, what's your problem?

Bye.

 

[Be_on_edge]

in the office we have a couple of ws with xp32 and picture 1800, what's your problem?

Bye.

then, in the settings of the video card I hold the antialias access to 8x, it happens that opening in sequence 3-4 3d models, the pc is freeza for about 30 seconds. Then it comes back to work.

the thing is quite annoying to the point that I gave up and I keep the anti-alysis off.

I tried 7 different drivers and the result is the same. I tried on st, st2 and st3 and the result does not change.

if imposed the antialias at 32x works well, but the performance definitely drops.

Can you try on a workstation to activate the card antialias and see if it works well?

if you need screenshot place of the settings to use.

Thank you.

p.s.: inside if I keep the antialias turned off as it does not work during rotations and it is to set for each file that opens.

 

[cacciatorino]

That's how I do the fx700m picture I have on my laptop, when I go in sketch mode (every so, not in a systematic way). it seems to me that in the past on another pc I had solved by passing from "guided by the graphics card (advanced)" to "guided by the graphics card (base)".

Take a test.

 

[Be_on_edge]

That's how I do the fx700m picture I have on my laptop, when I go in sketch mode (every so, not in a systematic way). it seems to me that in the past on another pc I had solved by passing from "guided by the graphics card (advanced)" to "guided by the graphics card (base)".

Take a test.

already tried, without success:frown:

france

 

[radio]

I asked my colleague this morning, who has on his ws the 1800s, to enable antialiasing, but for the moment did not find any block of the prog. (se18).

Bye.

 

[Be_on_edge]

no one who has st or st2 or st3 and fx 1800 painting?

 

[Tequila]

no one who has st or st2 or st3 and fx 1800 painting?

has work I have the fx3800 on xp32 I had the st2 and now the st3 but never gave problems, although I don't think you can compare it to fx1800

 

[Moskiz]

in the office my colleague uses fx1800 on st3 64bit with xp64 bit and has no problem

 

[Be_on_edge]

in the office my colleague uses fx1800 on st3 64bit with xp64 bit and has no problem

Unfortunately I am just looking for someone with picture fx 1800, xp 32 bit and st3 (or st2 or even st).

 

[tomasimattia]

hi, I have an fx picture of the hp, I use other programs cad though I made three firmware updates, controller if you have available them

 

[Be_on_edge]

hi, I have an fx picture of the hp, I use other programs cad though I made three firmware updates, controller if you have available them

Also mine comes from hp, I searched on their site but the only firmware update that I find is equivalent to what already on the card.

Do you have a link?

france

 

[Tequila]

Do one last test if you haven't done it. on the site of the nvidia is available the new driver released on March 02... Hopefully, if you haven't updated, you'll solve the problem.

version:267.17 whql
release date:2011.03.02
operating system:windows xp
language: italian
size:92.1 mb

 

[Tequila]

have you solved the problem or are you always at the starting point?
Hi.

 

[Be_on_edge]

have you solved the problem or are you always at the starting point?
Hi.

No, I didn't. I expected it, I practically tried all the drivers released from 2009 to today.

I'm trying to change my card.

Hi.