solidworks 2014 - realview graphics

[Rich7]

I'd like to know if there's a solution to my problem... I have solidworks 2014 and have disabled the function in question (realview graphics) how do I enable it???? I have a macbook pro retina 13 with windows 7 on bootcamp partition! with an integrated graphics card intel (r) hd graphics 4000 (in my opinion recent and sufficent to see two shadows and effects). I have read all the other solutions on the official website and I have not even tried the recommended patch (3.7 new) but it does not work... What? ? ?

 

[meccanicamg]

disabled realciew graphics? you will have chosen one of the 5 modes in view 3d. in the middle of the window at the top there is the button. But there is also a guide.

the real mode is active for supported tabs as a picture nvidia. if you have a low-level card you can't do much, especially if it doesn't have good performance even for which it was born.
Mac... I would say if you want to work you have to use a pc.

 

[Rich7]

disabled realciew graphics? you will have chosen one of the 5 modes in view 3d. in the middle of the window at the top there is the button. But there is also a guide.

the real mode is active for supported tabs as a picture nvidia. if you have a low-level card you can't do much, especially if it doesn't have good performance even for which it was born.
Mac... I would say if you want to work you have to use a pc.

thank you for the attention, "distised" in the sense that you can not select in any way is "gray" to the mouse passage is obscured in fact on the guide there is everything explained, but I wanted to know if there is any procedure with external programs such as: patches, executables, drivers etc. to activate it since I have a great mac(recent) with a good tab...and regarding the choice of the mac instead of pc I made it for other reasons that I do not want to express or start other discussions about it... since in my opinion they could very well provide a version of solidwork for mac, but their commercial decisions so I have to for strength partition. . Thanks anyway

 

[meccanicamg]

realize that your gpu can be compared to a nvidua geforce gt 330m and to say the truth already a year ago the nvidia 4xx and 5xx so I would say that it is already low as a video card. If somehow you could activate it you would find a very slowing down and eventually you couldn't work on it. already under current conditions you can not handle complex assemblies and therefore it is not that you can do much.... 20/30 pz, toolbox maybe something. put into the table difficult and slow... In short, it is not put very well as hardware to make jobs from 200/300 or more pieces. so you have to invent light loads, seen in draft quality, few sections, better no toolbox etc.
If you want to make fem, we don't go far, even if the processor can help you. You could use the redding module but it would be slow and it would heat the gpu a lot.
What do you have to do with it?

 

[marcof]

thank you for the attention, "distised" in the sense that you can not select in any way is "gray" to the mouse passage is obscured in fact on the guide there is everything explained, but I wanted to know if there is any procedure with external programs such as: patches, executables, drivers etc. to activate it

Try from here to see if you find any ideas.https://www.google.it/search?q=hd+g...p+solidworks+hd+graphics+4000+opengl+support+

since I have a great mac(recent) with a good tab.. .

it will be good, but surely in opengl works worse than any frame card of 5 or 6 years ago.

and regarding the choice of the mac instead of pcs I made it for other reasons that I do not want to express or start other discussions about it... since in my opinion they could very well provide a version of solidwork for mac, but their commercial decisions therefore I have to partition. . Thanks anyway

you will have very good reasons to have chosen a mac, among which those of not need to use programs that run only on windows and that require certified video cards that on the mac you can not mount because, seen software that turn on the mac, such cards do not need. If you were studying mechanical engineering, for example, you would probably have taken a pc to watch all these useless bangs you're going to meet now.

 

[Rich7]

What do you have to do with it?

I thank you for the prompt response and for the attention dedicated to me...I learned more or less the problem to respond to both, you study mechanical engineering. I needed more than anything to make small assemblies without having huge demands as in professional studies etc. Thank you again for the advice! I will now provide perhaps with a solution of an external video card to connect to my mac if possible, or to pass directly to a pc. thanks and greetings