roototrallatric coclea

[anonto]

Damn rs4 looks a lot like the real one.
Today I did not have a moment of time, tomorrow I place the photo with the two engaged screws, which I discovered to be mounted with a difference of 90° each other (as well as being symmetries).

Unfortunately, the company where I work doesn't want me to publish material, so I can't post the video, but for me it was fascinating (but in private I can send it to you); )

 

[anonto]

attach the two screws engaged with products (the direction is always from right to left)

 

[RS4]

Does it seem to me or any of the two faces of the cochlea are perpendicular to the bottom? in the central part of the original cochlea one of the two faces (tools the fittings) is always perpendicular to the bottom and the other has a angle greater than 90°.
What profile did you use to cut?
Can you describe how the sweep command options work to control rotation or profile change?
that of caia seems definitely a sophisticated command

Hello, Marco. .

perhaps the image does not make but the movement and perpendicular to the floor only rotates the propeller to be able to give the corner to the container and to release it. .

when it concerns the sweep function that I used, and along the reference surface in this case the yz plan, but I could have also used the function with the extraction direction do the same thing, for the first 3 constant coils to 10° I set the initial angle already to 10° constant... for the successive spires I resumed the angle at 0° initial and final 10 15 20° etc. applying in this case a function law of type s, that is that as it wraps reaches the final degree and at half spira is found half gradation, example if at the final and 15° half way and 7.5°

allego explanatory images and mathematical model

I don't have time. would be nice to see him moving

rotten places the video of youtube can't go

 

[marcof]

Hello, Marco. .

perhaps the image does not make but the movement and perpendicular to the floor only rotates the propeller to be able to give the corner to the container and to release it. .

Yes, that was clear to me, but I was referring to the fact that you used a sketch profile with both non-orthogonal faces compared to the bottom of the excavation.

when it concerns the sweep function that I used, and along the reference surface in this case the yz plan, but I could have also used the function with the extraction direction do the same thing, for the first 3 constant coils to 10° I set the initial angle already to 10° constant... for the successive spires I resumed the angle at 0° initial and final 10 15 20° etc. applying in this case a function law of type s, that is that as it wraps reaches the final degree and at half spira is found half gradation, example if at the final and 15° half way and 7.5°
allego explanatory images

Mick!! really powerful.
I the other day when I tried to gun a little and to get that result swx sweep funzone is unusable. I had to make a loft cut, but it takes minimum 3 sections per lap otherwise with two sections on the same floor does not follow the guide curve (the helid). I have put 4 per turn and on 8 turns you no longer pass to select them one at a time and place the profile alignment connectors in the right place, but you do.
the advantage of using the loft is to be able to change shape to each cutting profile as it happens in the real augmentation. if I have time for one of these nights complete the model and place.
with catia can you also change to each step as well as the orientation even the quotas of the sweep profile? don't tell me no, otherwise it's a catorcio of software and should give it with dixan:redface:

 

[RS4]

Yes, that was clear to me, but I was referring to the fact that you used a sketch profile with both non-orthogonal faces compared to the bottom of the excavation.

I didn't understand but he's orthogonal on the plan anyway


Mick!! really powerful.
I the other day when I tried to gun a little and to get that result swx sweep funzone is unusable. I had to make a loft cut, but it takes minimum 3 sections per lap otherwise with two sections on the same floor does not follow the guide curve (the helid). I have put 4 per turn and on 8 turns you no longer pass to select them one at a time and place the profile alignment connectors in the right place, but you do.
the advantage of using the loft is to be able to change shape to each cutting profile as it happens in the real augmentation. if I have time for one of these nights complete the model and place.
with catia can you also change to each step as well as the orientation even the quotas of the sweep profile? don't tell me no, otherwise it's a catorcio of software and should give it with dixan:redface:

what you say to use multiple profiles does it in the loft as in swx, I believe in the sweep that I know rotates the profiles as explained previously. .

but still there are many options in ca... there is also the adaptive sweep.. A mess

you place image of a challenge made long ago on loft placement with different sections here in the forum

the sections in red as you see different also as a very powerful type as a command

apologies the offtopic anonto

 

[anonto]

But, you know, it's still interesting, and something tells me I'm gonna have to learn catheia to work on the cochleas.
Having to then make simulations with all 3d objects, from catia to swx can I export a 3d and then use it on swx?
or do I want to do everything on catia (as long as it is possible)?

 

[RS4]

But, you know, it's still interesting, and something tells me I'm gonna have to learn catheia to work on the cochleas.
Having to then make simulations with all 3d objects, from catia to swx can I export a 3d and then use it on swx?
or do I want to do everything on catia (as long as it is possible)?

Hi anonto.. I don't know swx but I'm very sure he can do these jobs quietly... maybe better than catia... in some cases trusted.. and a great product ... study it.. I've heard and seen it on the forum of things he does.

Catia and very complex and Moroccan.. eventually succeeds...

I never agree to go from a cad to another exchange between iges and step... then how you come back.. .for all

 

[anonto]

Sorry to bother rs4, but can you give me a video or a guide on how to get that coclee?
I am an absolute novice of catia and I don't know where to start